Mo/Al/Mo结构电极的坡度角和关键尺寸差研究

刘丹; 秦刚; 蔡卫超; 王百强; 周禹; 饶毅; 李晨雨; 刘涛; 段海洋; 樊根瑞; 吕俊君

doi:10.3788/YJYXS20173211.0877

您当前的位置：

首页 >

文章列表页 >

Mo/Al/Mo结构电极的坡度角和关键尺寸差研究

材料科学 | 更新时间：2020-08-12

- Mo/Al/Mo结构电极的坡度角和关键尺寸差研究
- Profile and critical dimension bias of Mo/Al/Mo electrode
- 液晶与显示 2017年32卷第11期页码：877-885
- 作者机构：
  
  重庆京东方光电科技有限公司光刻工程部, 重庆 400700
- 作者简介：
  
  [ "刘丹(1988-), 男, 重庆忠县人, 硕士研究生, 2014年于四川大学取得硕士学位, 从事光刻方面工作。E-mail:liudan_cq@boe.com.cn" ]
- 基金信息：
- DOI：10.3788/YJYXS20173211.0877
  中图分类号： TP394.1;TH691.9
- 收稿日期：2017-06-16，
  
  录用日期：2017-8-16，
  
  纸质出版日期：2017-11-05
- 稿件说明：
移动端阅览
刘丹, 秦刚, 蔡卫超, 等. Mo/Al/Mo结构电极的坡度角和关键尺寸差研究[J]. 液晶与显示, 2017,32(11):877-885.

Dan LIU, Gang QIN, Wei-chao CAI, et al. Profile and critical dimension bias of Mo/Al/Mo electrode[J]. Chinese journal of liquid crystals and displays, 2017, 32(11): 877-885.
刘丹, 秦刚, 蔡卫超, 等. Mo/Al/Mo结构电极的坡度角和关键尺寸差研究[J]. 液晶与显示, 2017,32(11):877-885. DOI： 10.3788/YJYXS20173211.0877.

Dan LIU, Gang QIN, Wei-chao CAI, et al. Profile and critical dimension bias of Mo/Al/Mo electrode[J]. Chinese journal of liquid crystals and displays, 2017, 32(11): 877-885. DOI： 10.3788/YJYXS20173211.0877.

摘要

Mo/Al/Mo结构金属作为TFT的电极，刻蚀后的坡度角和关键尺寸差是重要的参数。明确影响坡度角和关键尺寸差的工艺参数，进而控制坡度角和关键尺寸差，这对工艺制程至关重要。本文探究了膜层结构、曝光工艺、刻蚀工艺对坡度角和关键尺寸差的影响，并对刻蚀工艺进行正交试验设计。实验结果表明：Al膜厚每减小60 nm，坡度角下降约9°，关键尺寸差增加0.1

m。曝光工艺中，显影后烘烤会增加光阻粘附力，导致关键尺寸差减小0.1

m，同时坡度角增加约9°。刻蚀工艺中，过刻量每增加10%，坡度角下降3.3°，关键尺寸差增加0.14

m；正交试验结果表明，对关键尺寸差、刻蚀均一性、坡度角影响因素的重要性顺序是：液刀流量＞Air Plasma电压＞水刀流量。经上述探究表明，坡度角和关键尺寸差呈负相关关系，刻蚀程度增加，关键尺寸差增加，而坡度角则减小。可以通过调节工艺参数对坡度角和关键尺寸差进行控制。

Abstract

At present

Mo/Al/Mo structural film is electrode material in TFT-LCD industry due to its advantages. The Critical Dimension Bias which is short for CD Bias and the Profile of Mo/Al/Mo electrode after etch process are important parameters which determine the TFT pattern and TFT characteristic. Therefore

it is necessary to identify the process parameters affecting profile and CD Bias in mass production

aiming at making profile and CD Bias under control

which would improve production yield and quality. In this paper

the effects of film structure

photo condition and etch condition on profile and CD Bias are comprehensively studied. What's more

orthogonal design for wet etch condition is conducted

which makes it possible to understand the order of importance for wet etch process parameters. The experimental results show that aluminum film thickness decreases by about 60 nm

profile will decrease by about 9ånd CD Bias will increase by 0.1

m at the same time. When it comes to photo condition

hard bake after developing process would enhance the adhesion between photo resist(PR) and metal. They will make CD bias decrease by about 0.1um and profile correspondingly increase by about 9°. The over etch degree increases by 10%

profile will decrease by about 3.3ånd CD Bias will correspondingly increase by about 0.14

m. The results of the orthogonal test show that the order of importance affecting CD Bias

profile and uniformity is as follows:Chemical Knife flow

Air plasma(AP) voltage

DI water Knife flow. Through the above research

it is found that profile and Bias are negatively correlated:The profile will decrease and CD Bias will increase when over etch degree increases. It is possible to make profile and CD Bias under control by adjusting the process parameters.

关键词

Keywords

references

谢振宇. a-Si TFT用氮化硅薄膜的制备及其性能研究[D]. 成都: 电子科技大学, 2007. http://cdmd.cnki.com.cn/article/cdmd-10614-2007050720.htm

XIE Z Y. The study of fabrication and performance of SiN x used in a-Si TFT[D]. Chengdu:University of Electronic Science and Technology of China, 2006. (in Chinese)

孟祥琦. 铝合金材料的应力腐蚀及腐蚀疲劳特性实验研究[D]. 上海: 上海交通大学, 2012. http://cdmd.cnki.com.cn/Article/CDMD-10248-1013020646.htm

MENG X Q. Experimental study on stress corrosion and corrosion fatigue behavior aluminum alloy materials[D] Shanghai:Shanghai Jiao Tong University, 2012. (in Chinese)

汪梅林, 于春崎, 汪永安.像素设计中沟道宽和长的选择[J].现代显示, 2007(5):24-26.

WANG M L, YU C Q, WANG Y A. The choice of channel width and lengh in pixel design[J]. Advanced Display, 2007(5):24-26.(in Chinese)

林鸿涛, 王明超, 姚之晓, 等. TFT-LCD中画面闪烁的机理研究[J].液晶与显示, 2013, 28(4):567-571.

LIN H T, WANG M C, YAO Z X, et al. Mechanism research about Flicker in TFT-LCD[J]. Chinese Journal of Liquid Crystals and Displays, 2013, 28(4):567-571. (in Chinese)

KA J, CHO E N, LEE M J, et al. Electrode metal penetration of amorphous indium gallium zinc oxide semiconductor thin film transistors[J]. Current Applied Physics, 2015, 15(6):675-678.

BAEK K H, YOON Y S, PARK J M, et al. A fluorine-related passivation layer on etched Al-Cu(1%) alloy surfaces on silicon after SF 6 plasma treatments[J]. Materials Letters, 35(3/4):183-187.

HWANG S J, LEE J H, JEONG C O, et al. Effect of film thickness and annealing temperature on hillock distributions in pure Al films[J]. Scripta Materialia, 2007, 56(1):17-20.

KIM D K, NIX W D, VINCI R P, et al. Study of the effect of grain boundary migration on hillock formation in Al thin films[J]. Journal of Applied Physics, 2001, 90(2):781-788.

林鸿涛, 王鹏.长期存放条件下TFT阵列基板栅金属线腐蚀原因分析[J].现代显示, 2006(7):50-52, 16.

LIN H T, WANG P.The corrosion of the TFT's metal lines[J]. Advanced Display, 2006(7):50-52, 16. (in Chinese)

肖亮, 张勋泽, 朴祥秀.载盘预处理对纯铝薄膜小丘生成的影响[J].液晶与显示, 2017, 32(2):104-109.

XIAO L, ZHANG X Z, PIAO X X. Effect of pretreatment of tray on hillock formation in pure Al films[J]. Chinese Journal of Liquid Crystals and Displays, 2017, 32(2):104-109. (in Chinese)

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

TFT-LCD制造工艺中金属或金属复合膜层坡度角的研究