TFT光刻DICD均一性改善优化

张玉虎; 岳浩; 王军帽; 李亚文

doi:10.3788/YJYXS20163110.0929

您当前的位置：

首页 >

文章列表页 >

TFT光刻DICD均一性改善优化

材料与器件 | 更新时间：2020-07-07

- TFT光刻DICD均一性改善优化
- Improvement of uniformity of TFT lithography DICD
- 液晶与显示 2016年31卷第10期页码：929-935
- 作者机构：
  
  合肥京东方光电科技有限公司, 安徽合肥 230012
- 作者简介：
  
  张玉虎(1983-), 男, 安徽霍邱人, 硕士研究生, 高级工程师, 2010年于合肥工业大学获得硕士学位, 主要从事光刻设备维护及工艺改善工作。E-mail:zhangyuhu@boe.com.cn
- 基金信息：
- DOI：10.3788/YJYXS20163110.0929
  中图分类号： TN305.7
- 收稿日期：2016-06-16，
  
  录用日期：2016-7-22，
  
  纸质出版日期：2016-10
- 稿件说明：
移动端阅览
张玉虎, 岳浩, 王军帽, 等. TFT光刻DICD均一性改善优化[J]. 液晶与显示, 2016,31(10):929-935.

Yu-hu ZHANG, Hao YUE, Jun-mao WANG, et al. Improvement of uniformity of TFT lithography DICD[J]. Chinese journal of liquid crystals and displays, 2016, 31(10): 929-935.
张玉虎, 岳浩, 王军帽, 等. TFT光刻DICD均一性改善优化[J]. 液晶与显示, 2016,31(10):929-935. DOI： 10.3788/YJYXS20163110.0929.

Yu-hu ZHANG, Hao YUE, Jun-mao WANG, et al. Improvement of uniformity of TFT lithography DICD[J]. Chinese journal of liquid crystals and displays, 2016, 31(10): 929-935. DOI： 10.3788/YJYXS20163110.0929.

摘要

为了对TFT（Thin Film Transistor）光刻DICD（Develop Inspection Critical Dimension）均一性进行改善，分析了光刻DICD存在差异性的原因，并建立了改善循环流程。对循环流程改善原理及方法进行说明。首先，根据处于光刻系统最佳焦平面位置光刻胶吸收光强最大，DICD最小（DICD

min

）原则，提出了调整光刻平面，使其与系统最佳焦平面趋势一致，可减小DICD差异性。接着，计算出各光刻区域与最佳焦平面位置处的DICD差值（DICD-DICD

min

），并通过结合光刻区域台板平坦度，判断DICD-DICD

min

各差值的正负性。然后，采用最小二乘法对光刻区域DICD-DICD

min

进行平面方程拟合，该平面即为光刻趋势平面，并反映了光刻平面与光刻系统最佳焦平面的差异。最后，以此平面方程作为光刻机台板高度调整平面方程，并对光刻区域台板高度进行调整，从而使得实际光刻平面趋于系统最佳焦平面。结果表明：该方法连续实验3次，DICD均一性可改善30%以上。

Abstract

In order to improve the uniformity of TFT lithography DICD

the reason for the difference of the DICD is analyzed

and a cycle improvement process is established. Its principle and method is illustrated. First

based on the principle that the photo resist absorbs the maximum light intensity on the best focal plane of the lithography system

and the DICD value is also minimum. Therefore

if the lithography plane is adjusted and the lithography plane trend is consistent with the best focal plane trend

the difference of DICD will be minimum. Then the difference of the DICD between the lithography area and the best focal plane area(DICD-DICD

min

) is calculated

and the sign of DICD-DICD

min

is judged by combining the stage flatness of the lithography area. Then the plane equation of DICD-DICD

min

is fitted by the least square method

and the plane is just the lithography trend plane

which also reflects the difference between the lithography plane and the best focal plane. Finally

the plane equation is used to adjust the stage height of the lithography machine

and by adjusting the height of the stage in the lithography area

the lithography plane trend is consistent with the best focal plane trend. The results show that the uniformity of DICD can be improved by more than 30% by doing the experiment three times.

关键词

Keywords

references

黎午升, 惠官宝, 崔承镇, 等.在镜像投影曝光机上使用相移掩膜提高解像力的初步研究[J].液晶与显示, 2014, 29(4):544-547.

LI W S, HUI G B, CUI C Z, et al. Preliminary study on improving resolution on mirror projection mask aligner with phase shift mask[J]. Chinese Journal of Liquid Crystals and Displays, 2014, 29(4):544-547. (in Chinese)

曲连杰, 郭建, 史大为, 等.高分辨率显示用小孔设计技术[J].液晶与显示, 2015, 30(2):246-250.

QU L J, GUO J, SHI D W, et al. Tiny hole design for high resolution display[J]. Chinese Journal of Liquid Crystals and Displays, 2015, 30(2):246-250. (in Chinese)

谷至华.薄膜晶体管(TFT)阵列制造技术[M].上海:复旦大学出版社, 2007.

GU Z H.Thin Film Transistor (TFT) Array Manufacturing Technology [M]. Shanghai:Fudan University Press, 2007. (in Chinese)

缪小运.先进光刻系统中焦平面测量与控制的研究[D].上海:复旦大学, 2006.

MIU X Y.The study on the advanced lithography system of the focal plane measurement and control[D]. Shanghai:Fudan University, 2006. (in Chinese)

姜立娟, 李响, 唐拓.光刻线宽精度控制的研究[J].微机处理, 2005(2):12-13.

JIANG L J, LI X, TANG T. The Rearch of photolithography line width precision control[J]. Microprocessors, 2005(2):12-13. (in Chinese)

李小平, 陈飞彪.投影光刻机硅片调焦调平测量模型[J].光学学报, 2007, 27(11):1987-1991.

LI X P, CHEN F B. Measurement model of focusing and leveling measurement system for projection lithography tool[J]. Acta Optica Sinica, 2007, 27(11):1987-1991. (in Chinese)

霍晓程, 李小平.用最小二乘法拟合曲面方程[J].赤峰学院学报(自然科学版), 2009, 25(6):11-13.

HUO X C, LI X P. Fitting curved surface equation with least square method[J]. Journal of Chifeng University (Natural Science Edition), 2009, 25(6):11-13. (in Chinese)

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

TFT-LCD四次光刻工艺中的光刻胶剩余量

平板电脑类产品暗态均匀性影响因素的研究与改善

窄长型车载液晶显示屏黑画面漏光研究及改善

排气方式及工艺参数对等离子体刻蚀a-Si均一性的影响

湿法刻蚀FI CD均一性的影响因素及提高刻蚀均一性的研究