Mechanism and improvement of extruded white spot in thin and slim BLU

Sheng-guo TANG; Chun-lei DONG; Zi-yuan LIU; Hai-feng XU; Hai-xia XIANG; Zheng-yuan ZHANG; Peng SUI; Yong MA; Man ZHAO

doi:10.3788/YJYXS20183310.0836

您当前的位置：

首页 >

文章列表页 >

Mechanism and improvement of extruded white spot in thin and slim BLU

Material and Device | 更新时间：2020-07-06

- Mechanism and improvement of extruded white spot in thin and slim BLU
- Chinese Journal of Liquid Crystals and Displays Vol. 33, Issue 10, Pages: 836-843(2018)
- 作者机构：
  
  合肥鑫晟光电科技有限公司, 安徽合肥 230012
- 作者简介：
- 基金信息：
- DOI：10.3788/YJYXS20183310.0836
  CLC： TN942.1
- Received：25 June 2018，
  
  Accepted：05 July 2018，
  
  Published：05 October 2018
- 稿件说明：
移动端阅览
Sheng-guo TANG, Chun-lei DONG, Zi-yuan LIU, et al. Mechanism and improvement of extruded white spot in thin and slim BLU[J]. Chinese journal of liquid crystals and displays, 2018, 33(10): 836-843.
DOI：

Sheng-guo TANG, Chun-lei DONG, Zi-yuan LIU, et al. Mechanism and improvement of extruded white spot in thin and slim BLU[J]. Chinese journal of liquid crystals and displays, 2018, 33(10): 836-843. DOI： 10.3788/YJYXS20183310.0836.

摘要

介绍了背光源顶白不良，探讨了顶白的形成机理。研究发现表面光滑反射片对导光板网点间留白区域的挤压是产生顶白的根本原因。由此提出通过改善背板局部凸起高度和增加反射片粗糙度来改善顶白。结果表明：顶白发生率随背板局部凸起高度降低和反射片表面粗糙度增加而明显降低。控制模具凸棱厚度可调整回压量，进而降低背板局部凸起高度。模具凸棱厚度为0.05 mm时，背板局部凸起高度均值由无回压时的0.21 mm降低至0.11 mm，加速试验条件下对应顶白发生率由50%降低至18.7%；涂布不同大小粒子可调整反射片表面粗糙度。当反射片涂布Bead粒子径为40 μm，对应粗糙度为6.29 μm时，并搭配段差回压后背板，改善后背光源在加速试验条件下无顶白发生。同时，经光学、老化及振动测试，改善后背光源未发现其它相关不良。

Abstract

This paper reports the extruded white spot (EWS) of BLU and the associated caused reasons

and studies the impaction of the height of local convexity on back cover and the roughness of reflector film on EWS. The results show that the incidence of EWS significantly reduces with the decrease in the height of local convexity. Under the best back-pressure process

the mean value of local convexity decline from 0.21 mm to 0.11mm. Accordingly

the incidence of EWS declines from 50% to 18.7% during THO & VIB accelerated tests. The anti-EWS ability of reflector film is obviously improved with the increase in roughness. There is no EWS occurred

when the roughness is 6.29 μm together with using back-pressure back cover.

关键词

Keywords

references

季旭东. LCD背光源产品的新发展[J].液晶与显示, 2002, 17(2):119-127.

JI X D. New development of LCDs backlight[J]. Chinese Journal of Liquid Crystals and Displays, 2002, 17(2):119-127. (in Chinese)

马群刚.TFT-LCD原理与设计[M].北京:电子工业出版社, 2011.

MA Q G.Theory and Design of TFT-LCD [M]. Beijing:Publishing House of Electronic Industry, 2011. (in Chinese)

邱庆荣.关于超薄LED背光模组设计探讨[J].电子测试, 2017(11):99, 94.

QIUQ R. Discussion on the design of ultra-thin LED backlight module[J]. Electronic Test, 2017(11):99, 94. (in Chinese)

谢洪波, 李韬, 李富琳, 等. LED背光源中侧发光导光管长度与出光性能的关系[J].发光学报, 2011, 32(9):934-938.

XIE H B, LI T, LI F L, et al. Relationship between the length and emitted light property of side-emitting light pipe in led back light source[J]. Chinese Journal of Luminescence, 2011, 32(9):934-938. (in Chinese)

黄翀, 姜言森, 沈奕, 等.侧光式LED背光源的导光板网点设计[J].应用光学, 2008, 29(5):689-692.

HUANG C, JIANG Y S, SHEN Y, et al. Design of scattering netted dots on light guide plate of edge-lighting LED backlight[J]. Journal of Applied Optics, 2008, 29(5):689-692. (in Chinese)

Hanemann T. Refractive index modification of polymers using nanosized dopants[J]. SPIE, 2008, 6992:69920D.

郭立新. U型冲压件弯曲回弹的控制研究[J].机械设计与制造, 2012(9):237-239.

GUO L X. The study of springback control for the U-puching parts[J]. Machinery Design & Manufacture, 2012(9):237-239. (in Chinese)

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

No data

Related Author

No data

Related Institution

No data

AI问答

Address：No.3888 Dong Nanhu Road, Changchun, Jilin, China 130033 Postal code：130033
Tel：0431-86176059 Email：yjxs@ciomp.ac.cn
Technical support is provided by Beijing Founder electronics co., LTD 吉ICP备11002662号-17 京公网安备11010802024621
It is recommended to read the content of this site in Chrome&IE9+. Please switch to extreme mode in browser 360.
Cookies We use cookies to help provide and enhance our service and tailor content. By continuing, you agree to the use of cookies.

⁰